Martin Preuss
465e750e3c
avr: activate new led modules.
2025-08-25 10:22:50 +02:00
Martin Preuss
6e062d3f60
improve stats reporting
...
now again use three messages to transmit stats (much more efficient than
sending single values, also more acurate).
2025-08-25 10:22:05 +02:00
Martin Preuss
7efaf720cc
com2w: work in COM2W_Run, not in COM2W_Every100ms
2025-08-25 10:20:13 +02:00
Martin Preuss
66ac029a69
avr: introduce two more led modules.
...
- led_signal: blink 8 status bits (short=0, long=1)
- led_activity: blink for a short period after a trigger, e.g. for network
activity
2025-08-25 10:19:23 +02:00
Martin Preuss
bae188ddee
t03: added firmware using new uart_fd module.
2025-08-23 00:10:01 +02:00
Martin Preuss
87788fa93c
avr: wait for free CLK line on error when in flash mode
2025-08-23 00:09:39 +02:00
Martin Preuss
5013bb8e29
avr network app: only respond to ping request if dest address matches.
2025-08-23 00:09:01 +02:00
Martin Preuss
08d420a871
avr: added module uart_fd
...
This module uses hardware UART of MCUs in full duplex mode.
2025-08-23 00:08:25 +02:00
Martin Preuss
3a7951be16
com2w: added some recovery code, improved protocol.
...
after sending a byte wait for the same time when sending the last bit as
with the other bits (otherwise the last bit might get lost by slower
devices).
2025-08-20 23:27:17 +02:00
Martin Preuss
6a3f6be8a9
avr: improved timing for sending bytes via com2w interface.
...
Still quite different among devices but that's just prove that the protocol
works without prior synchronisation.
2025-08-20 20:48:55 +02:00
Martin Preuss
6c3926c1e4
avr: added a note regarding timing.
2025-08-19 23:36:58 +02:00
Martin Preuss
8467408fd8
avr: increased waittimes for com2w (too fast for 1MHz nodes).
2025-08-19 23:36:44 +02:00
Martin Preuss
6bb499740d
avr: use 16bit for brightness (actually, ADC only presents 10 bit).
2025-08-19 23:03:43 +02:00
Martin Preuss
fc073696f8
avr: tweaked timing for com2w transport layer.
2025-08-19 23:03:15 +02:00
Martin Preuss
102996f69f
avr: switched most devices to com2w interface now.
2025-08-18 18:47:13 +02:00
Martin Preuss
f9d721ac02
removed unused device nodes.
...
- n00
- n06
- n11
- n12
- n15
- n17
- n18
- n19
- n20
- n22
- n23
- r02
- r04
- x03
2025-08-18 18:46:46 +02:00
Martin Preuss
6bf8f03fbb
added node S03.
2025-08-18 18:07:34 +02:00
Martin Preuss
fa404a5fcf
increase number of runs to 10 (was: 2)
2025-08-18 18:06:56 +02:00
Martin Preuss
3592a745d3
introduce app "hub"
2025-08-18 18:06:35 +02:00
Martin Preuss
7c01aa255f
split wait for 50us (value 50000 doesn't work for 20MHz nodes).
2025-08-18 18:05:12 +02:00
Martin Preuss
d9e7d4df81
com2w*: allow for higher frequencies than 8MHz
...
to be used with node S03, which is run at 20MHz.
2025-08-18 18:04:30 +02:00
Martin Preuss
9b1badb310
avr: introduce reference counter for network buffers.
2025-08-18 18:03:24 +02:00
Martin Preuss
0dc4a3a952
avr: started adding COM2WN module.
2025-08-04 22:28:49 +02:00
Martin Preuss
32bd3bc2f9
added r06 again.
2025-08-04 22:26:26 +02:00
Martin Preuss
3f2ae9dd03
Revert "started working on mqtt support in aqhome-nodes"
...
This reverts commit 7fbc616ce4
2025-08-03 00:56:46 +02:00
Martin Preuss
7fbc616ce4
started working on mqtt support in aqhome-nodes
2025-08-03 00:56:22 +02:00
Martin Preuss
8c13f9fdf7
avr: started adding com2wn module (multiple com2w devices in one)
2025-08-03 00:55:52 +02:00
Martin Preuss
6c5dc21f6a
avr: started adding r06 device.
2025-08-03 00:55:21 +02:00
Martin Preuss
eb1392f3fd
avr: fixed apidoc.
2025-08-03 00:54:45 +02:00
Martin Preuss
2b25fed2cd
com2w1: follow changes in com2w0.
2025-07-21 18:25:17 +02:00
Martin Preuss
66b298d977
guard some changes on network data with CLI.
2025-07-20 23:15:46 +02:00
Martin Preuss
1091ec1dee
read CLK and DATA early.
2025-07-20 23:15:22 +02:00
Martin Preuss
d0b5f84316
adapt com2w1 from com2w0 (the latter is proven to work now).
2025-07-20 00:15:13 +02:00
Martin Preuss
ae1e4c3e37
avr: bootloader works with new com2w code.
2025-07-20 00:05:53 +02:00
Martin Preuss
78cbbf334e
com2w: alloc buffer after receiving message. receiving works now.
2025-07-19 17:47:52 +02:00
Martin Preuss
c8c12bb892
t03: use router app.
2025-07-19 17:08:39 +02:00
Martin Preuss
ae1853ba62
enable sending messages.
2025-07-19 17:08:19 +02:00
Martin Preuss
e8423ae97f
check dest address for ping requests.
2025-07-19 17:07:52 +02:00
Martin Preuss
597504fb08
t03: added test firmware.
2025-07-19 15:02:46 +02:00
Martin Preuss
59a0962420
added com2w0
2025-07-19 15:02:31 +02:00
Martin Preuss
323a5b76be
sync test.
2025-07-19 09:48:56 +02:00
Martin Preuss
b7234a6da2
start using new COM module in n27, r05 and t03.
2025-07-19 09:47:23 +02:00
Martin Preuss
4a5ba97b85
increase buffer size.
2025-07-19 09:46:06 +02:00
Martin Preuss
bdd710fc5c
avr: started working on new SPI-like COM protocol.
...
use a clock and a data line to introduce synchronisation into the
protocol to be able to work with the wide range of mcu speeds (no need for
exact timing, no need for exact calibration).
2025-07-19 09:42:02 +02:00
Martin Preuss
535a695c50
limit number of loops inside main_runLoop.
2025-07-12 20:16:34 +02:00
Martin Preuss
357ffe4e17
comonuartX: handle multiple messages in one run.
...
still there are NOBUF errors...
2025-07-12 20:09:40 +02:00
Martin Preuss
349b4a929a
use in instead of inr (SREG is always inside normal io space).
2025-07-12 20:08:54 +02:00
Martin Preuss
a06d245345
r05: disable OWI and ds18b20 modules (no time to handle those), increase buffers
2025-07-12 20:08:30 +02:00
Martin Preuss
83225c453d
Use uid to determine initial wait time after re-enum request.
2025-07-12 20:07:33 +02:00
Martin Preuss
fa94190345
fixed message description for FLASH_DATA.
2025-07-12 00:22:18 +02:00
