avr: started working on flash protocol.

avr/flash.asm

@@ -1,19 +1,5 @@
 
 
-; ***************************************************************************
-; data
-
-
-.dseg
-
-flashDataBegin:
-  flashCurrentAddress:     .byte 2
-  flashLastReceivedMsg:    .byte 2
-flashDataEnd:
-
-
-
-
 ; ***************************************************************************
 ; code
 
@@ -31,7 +17,7 @@ Flash_StartPage:
   push zh
     push zl
       ldi r16, ((PAGESIZE*2)-1)
-      and r16, zl
+      and zl, r16
       rcall Flash_ReadPageIntoPageBuffer
     pop zl
   pop zh
@@ -47,7 +33,7 @@ Flash_StartPage:
 
 Flash_FinishPage:
   ldi r16, ((PAGESIZE*2)-1)
-  and r16, zl
+  and zl, r16
   rcall Flash_ErasePage
   rcall Flash_WritePage
   ret
@@ -76,7 +62,7 @@ Flash_ReadPageIntoPageBuffer_loop:
       ldi r20, (1<<SPMEN)                       ; enable next SPM, write into temp page buffer
       rcall utilsDoSpm                          ; (R16)
       adiw ZH:ZL, 2
-      sbiw r25:r24, 2                           ;use subi for PAGESIZEB<=256
+      sbiw r25:r24, 2                           ; use subi for PAGESIZEB<=256
     brne Flash_ReadPageIntoPageBuffer_loop
   out SREG, r15
   ret

avr/flashproto.asm

@@ -0,0 +1,145 @@
+
+
+
+.equ CPRO_PACKET_FLASH_START_OFFS_MSGNUM = COM_MSG_OFFS_PAYLOAD+0 ; 2 bytes
+.equ CPRO_PACKET_FLASH_START_OFFS_ADDR   = COM_MSG_OFFS_PAYLOAD+2 ; 2 bytes
+
+.equ CPRO_PACKET_FLASH_ADDR_OFFS_MSGNUM  = COM_MSG_OFFS_PAYLOAD+0 ; 2 bytes
+.equ CPRO_PACKET_FLASH_ADDR_OFFS_ADDR    = COM_MSG_OFFS_PAYLOAD+2 ; 2 bytes
+
+.equ CPRO_PACKET_FLASH_DATA_OFFS_MSGNUM  = COM_MSG_OFFS_PAYLOAD+0 ; 2 bytes
+.equ CPRO_PACKET_FLASH_DATA_OFFS_DATA    = COM_MSG_OFFS_PAYLOAD+2 ; 2 bytes
+
+.equ CPRO_FLASH_ERROR_NONE       = 0
+.equ CPRO_FLASH_ERROR_BAD_MSGNUM = 1
+.equ CPRO_FLASH_ERROR_BAD_ADDR   = 2
+
+
+
+; ***************************************************************************
+; data
+
+
+.dseg
+
+flashDataBegin:
+  flashCurrentAddress:     .byte 2
+  flashLastReceivedMsg:    .byte 2
+flashDataEnd:
+
+
+
+
+; ***************************************************************************
+; code
+
+
+.cseg
+
+
+
+
+; ---------------------------------------------------------------------------
+; Enqueue a FLASHDATA_ACK packet.
+;
+; IN:
+; - R16: destination address
+; - R17: response code (0 if ok, error code otherwise)
+; - R19:R18: msg num
+; OUT:
+; - CFLAG: set if okay, clear otherwise
+; MODIFIED REGS: R6, R7, R8, R9, R10, R11, R12, R16, R17, X, Y (R3, R4, R15, R16, R17, R18, R19, R20, R21)
+
+CPRO_EnqueueFlashRsp:
+  mov r6, r16
+  mov r7, r17
+  mov r8, r18
+  mov r9, r19
+
+  rcall COM_AllocBufferAndGetXY ; (r16, r17, r21)
+  brcc CPRO_EnqueueFlashRsp_error
+
+  push xh
+    push xl
+      mov r16, r6
+      ldi r17, CPRO_PAYLOAD_FLAGS_SECONDS | (3<<CPRO_PAYLOAD_FLAGS_SHIFT_NUM)
+      ldi r18, CPRO_CMD_FLASH_RSP
+      rcall cproBeginMsgWithVariablePayload  ; (R3, R4, R16, R17, R18, R19, R20, R21, X)
+      st X+, r8                              ; 4: msg num (low)
+      st X+, r9                              ; 5: msg num (high)
+      st X+, r7                              ; 6: ACK or NAK
+    pop xl
+  pop xh
+  rcall cproCalcAndAddChecksumByte
+
+  ; mark buffer as enqueued with PRIO "important" (higher number of retries)
+  ldi r20, COM_BUFFER_PRIO_IMPORTANT
+  rcall COM_EnqueuePacket      ; (R15, R16)
+  brcc CPRO_EnqueueFlashRsp_error
+  sec
+  ret
+CPRO_EnqueueFlashRsp_error:
+  clc
+  ret
+
+
+
+; ---------------------------------------------------------------------------
+; Handle "FLASH_START" packet.
+;
+; IN:
+; - Y  : pointer to received buffer
+; OUT:
+; - CFLAG: set if handled, cleared otherwise
+;
+
+CPRO_HandleFlashStart:
+  ldd r21, y+(COM_BUFFER_OFFS_DATA+COM_MSG_OFFS_SRCADDR)  ; source address for later
+  
+  ; check message number
+  ldi r20, CPRO_FLASH_ERROR_BAD_MSGNUM          ; preset error code
+  ldd r16, y+(COM_BUFFER_OFFS_DATA+CPRO_PACKET_FLASH_START_OFFS_MSGNUM)
+  ldd r17, y+(COM_BUFFER_OFFS_DATA+CPRO_PACKET_FLASH_START_OFFS_MSGNUM)+1
+  tst r17
+  brne CPRO_HandleFlashStart_respond            ; high byte of first message number should be 0
+  cpi r16, 1
+  brne CPRO_HandleFlashStart_respond            ; low byte of first message number should be 1
+  
+  lds r16, flashLastReceivedMsg
+  lds r17, flashLastReceivedMsg+1
+  or r16, r17
+  brne CPRO_HandleFlashStart_respond            ; should be 0, otherwise operation already in progress
+  
+  sts flashLastReceivedMsg+1, r16               ; high byte: 0
+  ldi r16, 1
+  sts flashLastReceivedMsg, r16                 ; low byte: 1
+
+  ; check address
+  ldi r20, CPRO_FLASH_ERROR_BAD_ADDR            ; preset error code
+  ldd r16, y+(COM_BUFFER_OFFS_DATA+CPRO_PACKET_FLASH_START_OFFS_ADDR)
+  ldd r17, y+(COM_BUFFER_OFFS_DATA+CPRO_PACKET_FLASH_START_OFFS_ADDR)+1
+  mov r18, r16
+  mov r19, r17
+  subi r18, LOW(AQHOME_FW_START_ADDRESS_MAIN)   ; below start of main firmware?
+  sbci r19, HIGH(AQHOME_FW_START_ADDRESS_MAIN)
+  brcs CPRO_HandleFlashStart_respond
+
+  ; store address
+  sts flashCurrentAddress, r16
+  sts flashCurrentAddress+1, r17
+  clr r20                                       ; set response code to 0
+  ; fall through
+CPRO_HandleFlashStart_respond:
+  mov r16, r21 ; dest addr
+  mov r17, r20 ; response
+  lds r18, flashLastReceivedMsg
+  lds r19, flashLastReceivedMsg+1
+  rcall CPRO_EnqueueFlashRsp
+  sec ; message handled
+  ret
+
+
+
+
+
+